belt cover
英 [belt ˈkʌvə(r)]
美 [belt ˈkʌvər]
网络 皮带罩; 护带罩
双语例句
- Attach belt cover support 1 on the arm.
把皮带护罩支柱1安装到机架上。 - Place bobbin winder 3 in the belt cover, and position it so that it does not contact the machine arm or the belt cover before fixing it with wooden screws.
把绕线装置3放到皮带护罩里，调整到不接触机架和皮带护罩的位置，然后用木螺丝进行固定。 - To avoid possible accidents because of abrupt start of the machine, turn OFF the power to the machine when tilting the machine head or removing the belt cover and the V belt.
为了防止突然的起动造成人身事故，放倒缝纫机时，或卸皮带罩和V形皮带时，请一定关掉电源。 - Unscrew the fastening screws from the belt cover.
松开安全带盖的紧固螺钉。 - The Penglai Group in the Jiaobei Belt is the only cover of the Archaean to Early Proterozoic crystalline basement in East Shandong.
本文应用鲁东胶北隆起带上蓬莱群板岩中伊利石结晶度值测量，确定了蓬莱群经历过低绿片岩相（浅变带）区域变质。 - A motor shaft gap used for a sealing plate for a seal air channel is left between the belt pulley and the end cover of the motor shell.
在皮带轮同电机机壳端盖之间保留供密封风道用的密封板穿过的电机轴空隙位。 - Install a good motor according to installation, shall be equipped with conveyor belt cover.
安装好电机后应根据安装情况，配备传送带防护罩。 - Technological Process and Die Design for the Belt Sheave Forming technique and design of die for cover board of refrigerator
板制多楔皮带轮冲压工艺与模具设计冰箱中盖板冲压成形工艺与模具设计 - Application of cad/ cae in design of injection mould for safety belt protection cover support
CAD/CAE在安全带护盖支架注塑模设计中的应用 - Attach belt cover 2 on the arm and the support. The girder is braced against an erection bracket.
把皮带护罩2安装到机架和支柱上。梁支撑在塔柱上的一个施工托架上。 - Therefore, it has certain practical significance of extending contour shrub belt on large scale to speed up slope farmland harness, control soil and water loss on slope land, and effectively increase vegetative cover.
因此，大面积推广等高灌木带措施，对加快坡耕地治理速度，控制坡耕地水土流失，有效增加坡耕地植被，具有一定现实意义。 - Technological Analysis and Die Design of the Belt Wheel Cover
皮带轮罩的工艺分析及模具设计 - Study on Processability of PVG Belt Cover Compound and Relationship with Belt Carcass Bonding
PVG带全橡胶覆盖胶加工性能与带芯粘合质量关系的研究 - Study on Adhesion of R/ P Mine Conveyor Belt With NBR Cover
矿用***橡胶覆盖胶橡塑整芯输送带的粘合研究 - Improvement is made for crushing process by feeding materials form primary crushing directly into a fan-shaped bar screen under which an adjustable plate distributes the fines evenly on the belt conveyor followed by cover of coarse particles.
根据现场生产实际改用粉碎后的矿粒直接给入扇形孔条筛，筛下可调刮板使细粒均匀分布在皮带下面，粗粒复盖其上。